gas_handling_system
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
gas_handling_system [2013/12/13 21:05] pereira |
gas_handling_system [2013/12/13 21:16] pereira |
||
|---|---|---|---|
| Line 30: | Line 30: | ||
| ===== Preparation of Gas bottles ===== | ===== Preparation of Gas bottles ===== | ||
| - | * In Data-U6 | + | ==== In Data-U6 |
| * Ensure I265GV is closed to isolate focal plane vacuum chamber from the rest of the beamline | * Ensure I265GV is closed to isolate focal plane vacuum chamber from the rest of the beamline | ||
| * Confirm that the focal plane chamber is under vacuum | * Confirm that the focal plane chamber is under vacuum | ||
| - | * Confirm that the only open gas handling system valves are 4, 5, 6, 20, 21, and 22 | + | * Confirm that the only open gas handling system valves are **4, 5, 6, 20, 21, and 22** |
| - | * In the S3 vault | + | ==== In the S3 vault ==== |
| * Ensure that the gas handling system roughing pump is running and has a good vacuum | * Ensure that the gas handling system roughing pump is running and has a good vacuum | ||
| * The pump sits on the floor under the focal plane behind the south support post | * The pump sits on the floor under the focal plane behind the south support post | ||
| Line 47: | Line 47: | ||
| + | ===== Filling Ion Chamber with Gas ===== | ||
| - | Filling Ion Chamber with Gas | + | * Follow instructions under [[# |
| + | * Monitor the pressure of the focal plane vacuum chamber (as read out via the I264IG ion gauge) while detectors are being filled with gas; the pressure normally stays below 5E-5 Torr. | ||
| - | Follow instructions under PREPARATION FOR FILLING DETECTORS WITH GAS above | + | * Confirm that the detector pressure as indicated by the display labeled P.T. #1 reads below a couple of Torr |
| - | Monitor the pressure of the focal plane vacuum chamber (as read out via the I264IG ion gauge) while detectors are being filled with gas; the pressure normally stays below 5E-5 Torr. | + | |
| - | Confirm that the detector pressure as indicated by the display labeled P.T. #1 reads below a couple of Torr | + | |
| - | To zero this display: | + | |
| - | Click on the Slot 3 (PT1) tab to access the details page for PT #1 | + | |
| - | Click the Zero Sensor button | + | |
| - | Click the Valves tab at the top of the LabView window to return to the overview display of the gas handling system | + | |
| - | Close valve 6 | + | |
| - | Open valve 2; the flow reading at MFC #1 should jump momentarily | + | |
| - | Fill Ion chamber | + | |
| - | Enter the desired fill pressure and start the automatic filling process | + | |
| - | Click on the tab labeled Slot 8 (M-card) IC to access the page with the pressure set point control | + | |
| - | Enter the desired pressure (typically 300 Torr) in the field under the knob labeled Set Point | + | |
| - | Click button labeled Return to AUTO Mode on left to start filling/ | + | |
| - | Click the Valves tab at the top of the LabView window to return to the overview display of the gas handling system to monitor filling | + | |
| - | The flow readings for MFC #1 will increase and eventually disappear as the readout value overflows the display field (this is normal behavior) | + | |
| - | If necessary, the filling process can be stopped at any time by pressing the valve button labeled Close MFC #1 | + | |
| - | Open valve 9 | + | |
| - | The filling process will take several minutes | + | |
| - | When the detector is filled, close valve 5 | + | |
| + | * Close **valve 6** | ||
| + | |||
| + | * Open **valve 2**; the flow reading at MFC #1 should jump momentarily | ||
| + | |||
| + | * Fill Ion chamber | ||
| + | * Enter the desired fill pressure and start the automatic filling process | ||
| + | * Click on the tab labeled **Slot 8 (M-card) IC** to access the page with the pressure set point control | ||
| + | * Enter the desired pressure (typically 300 Torr) in the field under the knob labeled Set Point | ||
| + | * Click button labeled **Return to AUTO Mode** on left to start filling/ | ||
| + | * Click the **Valves** tab at the top of the LabView window to return to the overview display of the gas handling system to monitor filling. The flow readings for MFC #1 will increase and eventually disappear as the readout value overflows the display field (this is normal behavior) | ||
| + | * If necessary, the filling process can be stopped at any time by pressing the valve button labeled Close MFC #1 | ||
| + | * Open **valve 9** | ||
| + | * The filling process will take several minutes | ||
| + | |||
| + | * When the detector is filled, close **valve 5** | ||
| Filling CRDC1 and CRDC2 with Gas | Filling CRDC1 and CRDC2 with Gas | ||
gas_handling_system.txt · Last modified: 2023/05/11 11:29 by pereira
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 4.0 International
