preparation_for_tuning_the_s800
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
preparation_for_tuning_the_s800 [2013/12/13 20:25] pereira |
preparation_for_tuning_the_s800 [2013/12/13 20:28] pereira |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== Preparation for tuning ====== | ====== Preparation for tuning ====== | ||
| - | * [[Software overview]] | + | * [[Software|Software overview]] |
| * [[Electronics overview]] | * [[Electronics overview]] | ||
| * [[Gas handling system]] | * [[Gas handling system]] | ||
| Line 7: | Line 7: | ||
| * [[Turning magnets on/off]] | * [[Turning magnets on/off]] | ||
| * [[Magnetic-rigidity setting]] | * [[Magnetic-rigidity setting]] | ||
| - | |||
| - | ELECTRONICS, | ||
| - | data-U6 (south end) | ||
| - | Electronic location: two racks that contain all the electronics and patch panels. | ||
| - | Oscilloscope TEKSCOPE11 | ||
| - | Use: S800 detector/ | ||
| - | Location: | ||
| - | NMR Oscilloscopes | ||
| - | Use: NMR resonances display | ||
| - | Location: upper two shelves on right electronics rack | ||
| - | NIM bin | ||
| - | Location: below NMR scopes in right electronics racks | ||
| - | Use: Canberra HV supply for Object scintillator | ||
| - | Upper patch panels (top of left rack) | ||
| - | Cables 1-10: to object | ||
| - | Cables 11-20: | ||
| - | Cables 21-25: | ||
| - | Cable 26 is missing | ||
| - | Cable 27-50 should go to pivot point (mostly not connect in vault) | ||
| - | Middle patch panel (top of left rack) | ||
| - | Cables 51-70: | ||
| - | SHV cables 1-2: to object | ||
| - | SHV cables 6-10: should go to intermediate image box (apparently not connected in vault) | ||
| - | SHV cables 11-20: | ||
| - | |||
| - | S800 FP (top level of S3 vault) | ||
| - | Electronics location: | ||
| - | Patch panels: | ||
| - | SHV Cables 21-30: | ||
| - | Cables 51-70: | ||
| - | Cables 91-110: | ||
| - | |||
| - | Pivot point (bottom level of S3 vault) | ||
| - | Electronics location: | ||
| - | Patch panels | ||
| - | Cables 75-110: | ||
| - | Cables 70-80: | ||
| - | Cables 81-90: | ||
| - | Cables 91-110: | ||
| - | |||
| - | Intermediate Image (accessed via middle level of S3 vault) | ||
| - | Electronics location: | ||
| - | Patch panels (in electronics rack on top level of S3 vault) | ||
| - | Cables 21-25: | ||
| - | Cables 81-90: | ||
| - | |||
| - | Object position (access via middle level of S3 vault) | ||
| - | Electronics location: | ||
| - | Patch panels (mounted on object box support under object box) | ||
| - | Cables 11-20: | ||
| - | Cables 71-80: | ||
| - | SHV cables 1-2: to Data-U6 | ||
| - | |||
| - | |||
| - | |||
| - | |||
| - | |||
| - | |||
| - | |||
| - | |||
preparation_for_tuning_the_s800.txt · Last modified: 2015/10/27 09:32 by pereira
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 4.0 International
