Differences

This shows you the differences between two versions of the page.

--- s800_daq_tools [2015/10/20 10:10]
pereira [Scaler Display]
+++ s800_daq_tools [2015/10/26 15:46]
pereira
@@ Line 13: / Line 13: @@
     * [[#Controls tab]]
   * [[#How to run combined S800 + GRETINA]]
@@ Line 41: / Line 42: @@
 {{:wiki:Delay-Window.png|Delay Window}}
-This window appears when the "Init" button is pressed on the VME crate controller tab as part of the initial setup of the [[s800 daq tools#run control window|S800 USB daq]]. It can also be accessed by pressing the "Show GUIs" button. The delay module allows software configurable delays to be applied to each of the signals indicated in the Channel column, which then form the TDC stops. It is configurable to enable delays to be set with beam on target, as the needed delay may change depending on experimental conditions. There are four "Delay Inspect" channels which are routed to the patch panel in data-U6. These signals can be compared with any one of the four "Trigger Inspect" channels in order to set proper delays for the TDCs.
+This window appears when the "Init" button is pressed on the VME crate controller tab as part of the initial setup of the [[s800 daq tools#run control window|S800 USB daq]]. It can also be accessed by pressing the "Show GUIs" button. The delay module allows software configurable delays to be applied to each of the signals indicated in the Channel column, which then form the TDC stops. It is configurable to enable delays to be set with beam on target, as the needed delay may change depending on experimental conditions.
+Some important things to remember:
+  * There are four "Delay Inspect" channels (routed to the patch panel in data U6) which can be selected using the Delay GUI
+  * These "Delay Inspect" signals can be compared with any one of the four "Trigger Inspect" channels in order to set proper delays for the TDCs. The "Trigger Inspect" channels can be selected using the [[S800 DAQ tools#Trigger GUI|ULM trigger GUI]]
+  * TDCs of last 4 listed signals (including XF and object scintillators) are bypassed with cable delays and thus their delays cannot be controlled with the GUI. They can be inspected, however using the GUI
+  * It is possible to bypass the delay of a given channel by checking the "bypass" check box in the GUI
+  * The TDC delays can only be changed when the run control is stopped; must SAVE settings before starting run control not to overwrite adjustments being made
+  * The S800 trigger used as reference to calculate the ToF is from E1 up signal
+  * The signal delays controlled by the GUI (and not by cable delays) are not “pipelined” -- i.e., any new signals that arrive during the delay time of a previous signal are lost and thus deadtime is introduced into the system.  The signals delayed passively by cables are “pipelined” and thus are not subject to deadtime losses
@@ Line 54: / Line 65: @@
 ==== Scaler Display ====
-The GUI used to display scalers rates can be open from the icon **S800 Scalers** in the desktop of [[Software#u6pc5 (data U6)|u6pc5]]. The GUI includes two pages labeled "s800" and "ratios". Page "s800" includes all the scaler channels; page "ratios" displays ratio values calculated between several pairs of channels. In addition, the GUI includes a panel showing the time evolution of the live time calculated from the live-to-raw trigger ratio, and the live-to-raw clock ratio. The figure below shows the page "ratios" from the scaler GUI.
+The GUI used to display scalers rates can be open from the icon **S800 Scalers** in the desktop of [[Software#u6pc5 (data U6)|u6pc5]]. Alternatively, open a terminal on u6pc5, and type **./goscalers** from directory **/user/s800/converged_daq/scalers**.
+The GUI includes two pages labeled "s800" and "ratios". Page "s800" includes all the scaler channels; page "ratios" displays ratio values calculated between several pairs of channels. In addition, the GUI includes a panel showing the time evolution of the live time calculated from the live-to-raw trigger ratio, and the live-to-raw clock ratio. The figure below shows the page "ratios" from the scaler GUI.
 A list of scaler channels can be found [[Scaler Channel Description|here]].

S800 Documentation

User Tools

Site Tools

Differences

Page Tools