S800 Documentation

User Tools

Site Tools

Trace:
s800_daq_tools

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
Next revision Both sides next revision
s800_daq_tools [2020/03/04 18:00]
pereira [Trigger GUI] 		s800_daq_tools [2020/03/05 12:21]
pereira [Scaler Display]
Line 91: Line 91:
 The different signal going through the trigger scheme can be inspected in the Data-U6 oscilloscope. Simply right click on any of the wires to put that signal onto one of the four "Trigger Inspect" channels available at the patch panel of Data-U6, and connect that patch-panel cable to the oscilloscope. By inspecting the various delays, widths and overlaps the user trigger can be configured. The Trigger GUI is discussed in greater detail [[Trigger|here]]. The different signal going through the trigger scheme can be inspected in the Data-U6 oscilloscope. Simply right click on any of the wires to put that signal onto one of the four "Trigger Inspect" channels available at the patch panel of Data-U6, and connect that patch-panel cable to the oscilloscope. By inspecting the various delays, widths and overlaps the user trigger can be configured. The Trigger GUI is discussed in greater detail [[Trigger|here]].
  
-The Trigger (ULM) GUI allows the user to select the S800 timestamp clock: either the internally generated clock from the ULM, or an external clock from an ancillary system (e.g. GRETINA). In the latter case, you have to make sure to check the two boxes on the bottom of the Trigger GUI labeled "External timestamp clock" and "+The Trigger (ULM) GUI allows the user to select the S800 timestamp clock: either the internally generated clock from the ULM, or an external clock from an ancillary system (e.g. GRETINA). In the latter case, you have to make sure to check the two boxes on the bottom of the Trigger GUI labeled "External timestamp clock" and "external sync select".
  
 ==== Scaler Display ==== ==== Scaler Display ====
-The GUI used to display scalers rates can be open from the icon **S800 Scalers** in the desktop of [[Software#u6pc5 (data U6)|u6pc5]]. Alternatively, open a terminal on u6pc5, and type **./goscalers** from directory **/user/s800/converged_daq/scalers**.+The GUI used to display scalers rates can be open from the icon **S800 Scalers** in the desktop of [[Software#u6pc5 (data U6)|u6pc5]]. Alternatively, open a terminal on u6pc5, and type **./goscalers** from directory **/user/s800/s800daq/scalers**.
  
 The GUI includes two pages labeled "s800" and "ratios". Page "s800" includes all the scaler channels; page "ratios" displays ratio values calculated between several pairs of channels. In addition, the GUI includes a panel showing the time evolution of the live time calculated from the live-to-raw trigger ratio, and the live-to-raw clock ratio. The figure below shows the page "ratios" from the scaler GUI. The GUI includes two pages labeled "s800" and "ratios". Page "s800" includes all the scaler channels; page "ratios" displays ratio values calculated between several pairs of channels. In addition, the GUI includes a panel showing the time evolution of the live time calculated from the live-to-raw trigger ratio, and the live-to-raw clock ratio. The figure below shows the page "ratios" from the scaler GUI.
s800_daq_tools.txt ยท Last modified: 2023/10/19 17:25 by swartzj

Page Tools

Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 4.0 International
CC Attribution-Noncommercial-Share Alike 4.0 International Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki