This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
s800_spectcl [2014/12/10 11:44] pereira [Frequently used parameters for S800 SpecTcl] |
s800_spectcl [2018/05/02 16:20] pereira [S800 SpecTcl installation in S800 computer] |
||
---|---|---|---|
Line 1: | Line 1: | ||
====== S800 SpecTcl ====== | ====== S800 SpecTcl ====== | ||
- | SpecTcl is the NSCL's event data analysis tool used for online and offline data analysis during experiments involving the S800 spectrograph. The documentation is accessible at: http:// | + | SpecTcl is the NSCL's event data analysis tool used for online and offline data analysis during experiments involving the S800 spectrograph. The documentation is accessible at: http:// |
+ | **Important NOTES**: | ||
+ | * The S800 SpecTcl is run from the main directory **/ | ||
+ | * A S800 SpecTcl packet (compressed tar file) can be created for distribution to users. Instructions on how to create this packet can be found [[S800 SpecTcl# | ||
- | The SpecTcl Control has been adapted for special functions required for the analysis of S800 data. SpecTcl can be open by from computer [[Software# | ||
- | {{: | + | The SpecTcl Control has been adapted for special functions required for the analysis of S800 data. SpecTcl can be open by from computer [[Software# |
+ | Spectra definition files can be found in directory **/ | ||
+ | The figure below shows the GUI control of the S800 analysis. | ||
+ | |||
+ | {{: | ||
The inverse map which enables the trajectory reconstruction of the particles within the spectrograph beam line can be loaded. Snapshots of [[Detectors# | The inverse map which enables the trajectory reconstruction of the particles within the spectrograph beam line can be loaded. Snapshots of [[Detectors# | ||
Line 26: | Line 32: | ||
* **.tac**: the raw drift time of the electrons in the CRDCs which can be related to the y position via the mask calibration | * **.tac**: the raw drift time of the electrons in the CRDCs which can be related to the y position via the mask calibration | ||
* **.calc.x_gravity**, | * **.calc.x_gravity**, | ||
- | * .anode: amplitude of the CRDC anode signal (used for diagnostics) | + | * |
* **s800.fp.track** | * **s800.fp.track** | ||
* **.afp**: dispersive angle in the focal plane calculated from the x-y positions of the particles measured with the CRDCs | * **.afp**: dispersive angle in the focal plane calculated from the x-y positions of the particles measured with the CRDCs | ||
Line 97: | Line 103: | ||
+ | |||
+ | |||
+ | ===== S800 SpecTcl installation in S800 computer ===== | ||
+ | Before installing the S800 SpecTcl make sure to contact the S800 Device Physicist (Jorge Pereira). | ||
+ | In order to install S800 SpecTcl in the S800 computer, follow the following steps: | ||
+ | |||
+ | - Connect to s800 account, preferably from u6pc5. | ||
+ | - Check that the environment variable SPECTCLBINDIR is well defined: '' | ||
+ | - Go to **/ | ||
+ | - Clone the master branch from the remote repository: '' | ||
+ | - Type '' | ||
+ | - Goes to subdirectory **/ | ||
+ | - Goes to subdirectory **/src**, runs make clean, and make (this creates the SpecTcl binary) and moves it to the Main directory (up) | ||
+ | - Creates SpecTcl-running directory defined in **SPECTCLBINDIR=/ | ||
+ | - Moves " | ||
+ | - This gets the software necessary to run SpecTcl ready in directory **/ | ||
+ | - SpecTcl can now be run just by typing '' | ||
+ | |||
+ | |||
+ | ===== S800 SpecTcl deployment ===== | ||
+ | This section describes the procedure and scripts (Makefiles) to create a tar file with the S800 SpecTcl source files that any user may need to run S800 SpecTcl by themselves. This tar file contains: | ||
+ | |||
+ | * " | ||
+ | * **/src** subdirectory with source cpp and h files, Makefile, and libnumreclite.a library from Numerical Recipes | ||
+ | * **/ | ||
+ | * **/ | ||
+ | |||
+ | |||
+ | The procedure to deploy this software works as follows: | ||
+ | |||
+ | - Connect to s800 account, preferably from u6pc5. | ||
+ | - Check that the environment variable SPECTCLDEPLOY is well defined: '' | ||
+ | - Go to **/ | ||
+ | - Clone the master branch from the remote repository: '' | ||
+ | - Type '' | ||
+ | - Goes to subdirectory **/ | ||
+ | - Creates deployment directory defined in **SPECTCLDEPLOY=/ | ||
+ | - Moves " | ||
+ | - Compresses directory **/ | ||
+ | - Removes **/ | ||
+ | - The compressed file s800spectcl_deploy.tar.gz is located in the home directory **/ | ||