This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Last revision Both sides next revision | ||
to-do_list [2014/12/05 19:48] pereira [In S3 vault] |
to-do_list [2023/10/19 17:12] swartzj |
||
---|---|---|---|
Line 5: | Line 5: | ||
===== In S3 vault ===== | ===== In S3 vault ===== | ||
- | * Ensure that the object scintillator is in good conditions | + | |
+ | |||
+ | | ||
* [[Turning magnets on off#Arming of Dump Switch|Arm dump switches]] | * [[Turning magnets on off#Arming of Dump Switch|Arm dump switches]] | ||
Line 17: | Line 19: | ||
* Make sure Intermediate PPACs have gas | * Make sure Intermediate PPACs have gas | ||
- | ===== In data-U6 ===== | + | ===== In data U4 ===== |
- | * Start [[Software#u6pc5 (data U6)|Software applications]] (in computer | + | * Start [[Software#u4pc8 (data U4)|Software applications]] (in computer |
- | | + | |
- | * [[Turning magnets on/off#set s800 magnets settings|Put 10 Amps in Spectrograph dipoles]] | + | ==== Setting up DAQ software ==== |
+ | |||
+ | * For each experiment, an S800 Device Physicist will, after backing up whatever is to be backed up, install S800 DAQ and make it ready for the experiment. They do so as described in the following. | ||
+ | |||
+ | === Backup any updates === | ||
+ | |||
+ | * ~/ | ||
+ | * Compare files in the subdirectory Configurations (e.g. '' | ||
+ | * Manually add the modified filed and commit the changes, and '' | ||
+ | |||
+ | === Uninstall existing files === | ||
+ | |||
+ | * '' | ||
+ | * '' | ||
+ | |||
+ | === Install existing files === | ||
+ | |||
+ | * '' | ||
+ | * The script should relink **stagearea** to the right place, provided that the proper experimental number is given. After typing '' | ||
+ | |||
+ | === Set S800 DAQ mode === | ||
+ | |||
+ | * Set S800 DAQ in [[s800 daq tools# | ||
+ | |||
+ | * Check [[s800 daq tools# | ||
+ | |||
+ | ===== Other items ===== | ||
+ | |||
+ | * [[Turning magnets on/off#Set magnet currents individually | ||
* [[Gas handling system|Start gas in detectors]] | * [[Gas handling system|Start gas in detectors]] | ||
- | * Enable CRAD04 with a rate limit of 20 kHz (CRAD04 looks at E1 up FP scintillator) via PanelMate **CRAD_RF_Intlks.ui** (PAGE 01) | + | * Enable CRAD04 with a rate limit of 20 kHz (CRAD04 looks at E1 up FP scintillator) via PanelMate **CRAD_RF_Intlks.ui** (PAGE 01) located in directory \\exp\files\control\ncsdata\General\Qt\Templates |
+ | |||
* [[Magnetic-rigidity setting|Set spectrograph Brho]] (coordinate with experimenters) | * [[Magnetic-rigidity setting|Set spectrograph Brho]] (coordinate with experimenters) | ||
+ | |||
+ | |||
+ | |||
+ | |||
+ | ===== At the end of the experiment ===== | ||
+ | * Verify with S800 Device Physicist that S800 DAQ software is uninstalled. This can be done by typing script '' | ||
+ | |||
+ | * Unbias detectors, CRDC interface boards, CRDCs gate, etc | ||
+ | |||
+ | * [[Gas handling system|Remove gas]] from CRDCs and Ion Chamber | ||