tuning_the_s800_xdt
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
tuning_the_s800_xdt [2015/10/21 13:53] pereira |
tuning_the_s800_xdt [2015/10/21 16:09] pereira |
||
|---|---|---|---|
| Line 13: | Line 13: | ||
| === Send beam to FP === | === Send beam to FP === | ||
| * Ensure that the S800 spectrograph magnets are tuned to the right rigidity | * Ensure that the S800 spectrograph magnets are tuned to the right rigidity | ||
| + | |||
| + | * Verify that the beam blocker (labeled I255 Slits) in the S3 page of Barney is open: | ||
| + | * Expected " | ||
| * Ensure that CRAD04 (typically connected to object scintillator) is enabled with a rate limit of **20 kHz** (CRAD04 looks at E1 up FP scintillator) | * Ensure that CRAD04 (typically connected to object scintillator) is enabled with a rate limit of **20 kHz** (CRAD04 looks at E1 up FP scintillator) | ||
| Line 51: | Line 54: | ||
| * Adjust MCFD threshold: | * Adjust MCFD threshold: | ||
| + | * Open configuration file **MCFD16.tcl** in **/ | ||
| * The OBJ signal feeding this module is not patched out to data U6 | * The OBJ signal feeding this module is not patched out to data U6 | ||
| * The OBJ signal from MCFD-16 module goes to the Mesytec MTDC32 module and scaler (channel OBJ.MCFD.Scint) | * The OBJ signal from MCFD-16 module goes to the Mesytec MTDC32 module and scaler (channel OBJ.MCFD.Scint) | ||
| * Adjust CFD threshold looking at scalers. The ratio of OBJ to XFP scaler rates (channels OBJ.MCFD.Scint and XFP.MCFD.Scint) should reflect the transmission of the cocktail beam | * Adjust CFD threshold looking at scalers. The ratio of OBJ to XFP scaler rates (channels OBJ.MCFD.Scint and XFP.MCFD.Scint) should reflect the transmission of the cocktail beam | ||
| + | * Save new threshold in configuration file **MCFD16.tcl** | ||
| Line 96: | Line 100: | ||
| {{: | {{: | ||
| - | * Gains are controlled in **s800shpini.tcl** file in directory | + | * Gains are controlled in **s800shpini.tcl** file in directory |
| * First shaper is for ion chamber | * First shaper is for ion chamber | ||
| * Typically, only coarse gains are used | * Typically, only coarse gains are used | ||
| - | * Stop and start **[[s800 daq tools#Run Control Window|RunControl]]** to assert new gain values | + | * End and Begin **[[s800 daq tools#Run Control Window|ReadoutGUI]]** to assert new gain values |
| Line 108: | Line 112: | ||
| * Patched to data-U6 on labeled connector | * Patched to data-U6 on labeled connector | ||
| * **200 – 500 mV** signals are good | * **200 – 500 mV** signals are good | ||
| + | * CRDC1 anode is noisier (digital noise) than CRDC2 | ||
| * Bias CRDC1 and CRDC2. Typical starting values: | * Bias CRDC1 and CRDC2. Typical starting values: | ||
| * For He-3 @ ~130 MeV/u: CRDC1 (Anode=1120 V, Drift=1000 V); CRDC2 (Anode=1120 V; Drift=1000 V) | * For He-3 @ ~130 MeV/u: CRDC1 (Anode=1120 V, Drift=1000 V); CRDC2 (Anode=1120 V; Drift=1000 V) | ||
| Line 119: | Line 124: | ||
| * Count rate is a little higher than on scintillator due to noise or thresholds | * Count rate is a little higher than on scintillator due to noise or thresholds | ||
| - | * Check **[[s800 SpecTcl|Spectcl]]** window **S800_CRDCS.win** to verify the good performance of the detectors. (The spectra for each CRDC can be checked separatelly in windows **s800_CRDC1.win** and **S800_CRDC2.win**) | + | * Check **[[s800 SpecTcl|Spectcl]]** window **S800_CRDCS.win** |
| * Spectra **crdc1.raws** and **crdc2.raws** (top and middle spectra in the leftmost (first) column) | * Spectra **crdc1.raws** and **crdc2.raws** (top and middle spectra in the leftmost (first) column) | ||
| Line 126: | Line 131: | ||
| * Width of beam peak is proportional to A1900 p-acceptance in focus optics | * Width of beam peak is proportional to A1900 p-acceptance in focus optics | ||
| * Width is narrower in match optics | * Width is narrower in match optics | ||
| - | * Adjust anode HV to bring fuzzy maximum to around 600-700 channels (the ADC for each pad saturates | + | * Adjust anode HV to bring fuzzy maximum to around 600-700 channels (saturation of each pad at ~ 1000 ch) |
| * Spectra **crdc1.anode_crdc1.tac** and **crdc2.anode_crdc2.tac** (top and middle spectra in the second column) | * Spectra **crdc1.anode_crdc1.tac** and **crdc2.anode_crdc2.tac** (top and middle spectra in the second column) | ||
| Line 142: | Line 147: | ||
| | | ||
| * Spectra **crdc1.xg** and **crdc2.xg** (bottom spectra in first and second columns) | * Spectra **crdc1.xg** and **crdc2.xg** (bottom spectra in first and second columns) | ||
| - | * It shows the position of the beam in the dispersive direction, evaluated by calculating the " | + | * It shows the position of the beam in the dispersive direction, evaluated by calculating the " |
| - | * Spectra **crdc1.tac** and **crdc2.tac** (bottom spectra in third and fourth columns) | ||
| - | * They correspond to the non-dispersive position of the beam in the CRDCs. The peak should be in the middle of the spectra in order to center the beam | ||
| + | * Spectra **crdc1.tac** and **crdc2.tac** (bottom spectra in third and fourth columns) | ||
| + | * They correspond to the non-dispersive position of the beam in the CRDCs. | ||
| {{: | {{: | ||
tuning_the_s800_xdt.txt · Last modified: 2023/09/22 15:15 by swartzj
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 4.0 International
