tuning_the_s800_xdt
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
tuning_the_s800_xdt [2015/10/27 14:24] pereira [Setting up Reaction Settings] |
tuning_the_s800_xdt [2015/10/27 16:42] pereira [Send beam to FP] |
||
|---|---|---|---|
| Line 18: | Line 18: | ||
| * Expected " | * Expected " | ||
| - | * Ensure that CRAD04 | + | * Ensure that CRAD04 is enabled with a rate limit of **20 kHz** (CRAD04 looks at E1 up FP scintillator) |
| * Remember: S800 FP rate limit is **6 kHz** | * Remember: S800 FP rate limit is **6 kHz** | ||
| Line 155: | Line 155: | ||
| * They correspond to the non-dispersive position of the beam in the CRDCs. | * They correspond to the non-dispersive position of the beam in the CRDCs. | ||
| - | {{: | + | {{: |
| Line 310: | Line 310: | ||
| * Reaction setting to FP | * Reaction setting to FP | ||
| * Start with Attenuator setting of unreacted beam and step up in intensity | * Start with Attenuator setting of unreacted beam and step up in intensity | ||
| - | * Looking | + | * If necessary, set up beam blocker looking |
| + | * Click on label **I255 Slits** in the S3 page of Barney | ||
| * Expected " | * Expected " | ||
| * Expect to see unreacted beam if reaction setting is within +/- 3% of unreacted beam setting | * Expect to see unreacted beam if reaction setting is within +/- 3% of unreacted beam setting | ||
| Line 366: | Line 367: | ||
| - | |||
| - | |||
| - | ====== Follow-up ====== | ||
| - | |||
| - | * Before leaving beam with experimenters | ||
| - | * Set up current trip points on Linux HV controls | ||
| - | * Values used for K-48 | ||
| - | * 5 for CRDC and Ion Chamber anodes and intermediate image ppacs | ||
| - | * 50 for CRDC drifts | ||
| - | * 80 for IC drift | ||
| - | * Ensure alarms are running | ||
| - | * Make sure Linux HV GUI alarms are enabled | ||
| - | * Make sure threshold on isobutane level is set up (not currently connected to alarms because they give too many false alarms when communication is lost) | ||
| - | * All logs are being recorded | ||
| - | * There is no log file for biases controlled by Labview | ||
| - | * Linux HV | ||
| - | * LabView gas handling system | ||
| - | * Note in logbook | ||
| - | * Scintillator biases | ||
| - | * IC gate biases | ||
| - | * Post reference printouts for experimenters | ||
| - | * HV status: a snapshot of HV GUI | ||
| - | * Gas handling system status: a snapshot of LabView window | ||
| - | |||
| - | * Create window configuration with summing regions to make it easier for experimenters to track efficiency/ | ||
| - | |||
| - | * Setting up coincidences for additional reaction settings in an experiment | ||
| - | * Do not need to redo coincidence settup if secondary beam does not change | ||
| - | * Might need to redo coincidence setup if secondary beam changes drastically | ||
| - | |||
| - | * To watch during experiment | ||
| - | * Look for isobutene running out – messes up data over several hours | ||
| - | |||
| - | * Implementing dE- or TOF-based corrections is part of EXR | ||
| - | |||
| - | More detail needed | ||
| - | Minimum rates required for coincidence setup | ||
| - | Selection of appropriate substitute reactions for coincidence setup | ||
| - | How to feel comfortable that there will not be a problem with FP detector gases running out | ||
| - | Starting alarms | ||
| - | Starting logging | ||
tuning_the_s800_xdt.txt · Last modified: 2023/09/22 15:15 by swartzj
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 4.0 International
