This shows you the differences between two versions of the page.
Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
tuning_the_s800_xdt [2015/10/27 14:37] pereira [Follow-up] |
tuning_the_s800_xdt [2015/10/29 10:48] pereira [Timing setup] |
||
---|---|---|---|
Line 18: | Line 18: | ||
* Expected " | * Expected " | ||
- | * Ensure that CRAD04 | + | * Ensure that CRAD04 is enabled with a rate limit of **20 kHz** (CRAD04 looks at E1 up FP scintillator) |
* Remember: S800 FP rate limit is **6 kHz** | * Remember: S800 FP rate limit is **6 kHz** | ||
Line 74: | Line 74: | ||
* End and Begin **[[s800 daq tools#Run Control Window|ReadoutGUI]]** to assert new trigger condition | * End and Begin **[[s800 daq tools#Run Control Window|ReadoutGUI]]** to assert new trigger condition | ||
- | * Select **[[s800 SpecTcl|Spectcl]]** window **S800_SCINT.win** | + | * Select **[[s800 SpecTcl|Spectcl]]** window **S800_SCINT.win** in directory **/ |
* Adjust **[[hv bias|bias]]** looking at 2D spectra **e1.deup_e1.dedown** (showing the parameters s800.fp.e1.de_down vs. s800.fp.e1.de_up) for the FP E1 scintillator | * Adjust **[[hv bias|bias]]** looking at 2D spectra **e1.deup_e1.dedown** (showing the parameters s800.fp.e1.de_down vs. s800.fp.e1.de_up) for the FP E1 scintillator | ||
Line 94: | Line 94: | ||
- | * Select **[[s800 SpecTcl|Spectcl]]** window **S800_IC.win** | + | * Select **[[s800 SpecTcl|Spectcl]]** window **S800_IC.win** |
* Adjust pad gains | * Adjust pad gains | ||
Line 126: | Line 127: | ||
* Count rate is a little higher than on scintillator due to noise or thresholds | * Count rate is a little higher than on scintillator due to noise or thresholds | ||
- | * Check **[[s800 SpecTcl|Spectcl]]** window **S800_CRDCS.win** (see figure below) to verify the good performance of the detectors. (The spectra for each CRDC can be checked separatelly in windows **s800_CRDC1.win** and **S800_CRDC2.win**) | + | * Check **[[s800 SpecTcl|Spectcl]]** window **S800_CRDCS.win** in directory **/ |
* Spectra **crdc1.raws** and **crdc2.raws** (top and middle spectra in the leftmost (first) column) | * Spectra **crdc1.raws** and **crdc2.raws** (top and middle spectra in the leftmost (first) column) | ||
Line 165: | Line 166: | ||
* The three columns correspond to the **RF-FP** ToF (left), **OBJ-FP** (center), and **XFP-FP** (right) | * The three columns correspond to the **RF-FP** ToF (left), **OBJ-FP** (center), and **XFP-FP** (right) | ||
* The first (top) row corresponds to the Phillips TDC | * The first (top) row corresponds to the Phillips TDC | ||
- | * The second row corresponds to the MTDC with all the hits included | + | * The second row corresponds to the MTDC with all the hits included. Note that in a unreacted-beam setting, the first hit typically provides the " |
* The third row corresponds to the MTDC with only the first hit | * The third row corresponds to the MTDC with only the first hit | ||
* The fourth row corresponds to the ORTEC TACs. Note that there is not **RF-FP TAC** | * The fourth row corresponds to the ORTEC TACs. Note that there is not **RF-FP TAC** | ||
- | * The two spectra in the fifth row corresponds to the MTDC summary spectra of OBJ-FP and XFP-FP ToFs (zoomed in). The spectra show the ToF (vertical axis) vs. hit number (horizontal axis). | + | * The two spectra in the fifth row corresponds to the MTDC summary spectra of OBJ-FP and XFP-FP ToFs (zoomed in). The spectra show the ToF (vertical axis) vs. hit number (horizontal axis). |
* An empty ToF spectrum means that either the delays are not right (and need to be adjusted) or the spectrum range is too narrow | * An empty ToF spectrum means that either the delays are not right (and need to be adjusted) or the spectrum range is too narrow | ||
* The MTDC spectra should never be empty because the matching window is sufficiently wide (around 4000 ns) | * The MTDC spectra should never be empty because the matching window is sufficiently wide (around 4000 ns) | ||
Line 186: | Line 188: | ||
* Select SpecTcl window **S800_PID.win** in directory **/ | * Select SpecTcl window **S800_PID.win** in directory **/ | ||
* The three columns correspond to the PID determined with the **RF-FP** ToF (left), **OBJ-FP** (center), and **XFP-FP** (right) | * The three columns correspond to the PID determined with the **RF-FP** ToF (left), **OBJ-FP** (center), and **XFP-FP** (right) | ||
- | * The first (top) row corresponds to the Phillips TDC | + | * The first (top) row corresponds to PID spectra using the Phillips TDC |
- | * The second row corresponds to the MTDC with just the first hit included | + | * The second row corresponds to PID spectra using the MTDC with __just |
- | * The third row corresponds to the ORTEC TACs. Note that there is not **RF-FP TAC** | + | * The third row corresponds to PID spectra using the MTDC gated on the " |
+ | * The fourth row corresponds to PID spectra using the ORTEC TACs. Note that there is not **RF-FP TAC** | ||
* You might need to adjust the limits of the spectra to get a good resolution | * You might need to adjust the limits of the spectra to get a good resolution | ||