tuning_the_s800_xdt
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
tuning_the_s800_xdt [2015/10/29 13:21] pereira [Checking Particle ID and rate at S800 FP] |
tuning_the_s800_xdt [2017/05/26 16:08] pereira [Timing setup] |
||
|---|---|---|---|
| Line 68: | Line 68: | ||
| * Set trigger to “s800 trigger” | * Set trigger to “s800 trigger” | ||
| - | * Ensure that the **[[s800 daq tools# | + | * Ensure that the **[[s800 daq tools# |
| * Under trigger tab select **s800 trigger** (which is E1 up by definition) | * Under trigger tab select **s800 trigger** (which is E1 up by definition) | ||
| * Deselect experiment trigger | * Deselect experiment trigger | ||
| Line 74: | Line 74: | ||
| * End and Begin **[[s800 daq tools#Run Control Window|ReadoutGUI]]** to assert new trigger condition | * End and Begin **[[s800 daq tools#Run Control Window|ReadoutGUI]]** to assert new trigger condition | ||
| - | * Select **[[s800 SpecTcl|Spectcl]]** window **S800_SCINT.win** in directory **/ | + | * Select **[[s800 SpecTcl|Spectcl]]** window **S800_SCINT.win** in directory **/ |
| * Adjust **[[hv bias|bias]]** looking at 2D spectra **e1.deup_e1.dedown** (showing the parameters s800.fp.e1.de_down vs. s800.fp.e1.de_up) for the FP E1 scintillator | * Adjust **[[hv bias|bias]]** looking at 2D spectra **e1.deup_e1.dedown** (showing the parameters s800.fp.e1.de_down vs. s800.fp.e1.de_up) for the FP E1 scintillator | ||
| Line 94: | Line 95: | ||
| - | * Select **[[s800 SpecTcl|Spectcl]]** window **S800_IC.win** | + | * Select **[[s800 SpecTcl|Spectcl]]** window **S800_IC.win** |
| * Adjust pad gains | * Adjust pad gains | ||
| Line 127: | Line 127: | ||
| * Count rate is a little higher than on scintillator due to noise or thresholds | * Count rate is a little higher than on scintillator due to noise or thresholds | ||
| - | * Check **[[s800 SpecTcl|Spectcl]]** window **S800_CRDCS.win** in directory **/ | + | * Check **[[s800 SpecTcl|Spectcl]]** window **S800_CRDCS.win** (see figure below) to verify the good performance of the detectors. (The spectra for each CRDC can be checked separatelly in windows **s800_CRDC1.win** and **S800_CRDC2.win**) |
| * Spectra **crdc1.raws** and **crdc2.raws** (top and middle spectra in the leftmost (first) column) | * Spectra **crdc1.raws** and **crdc2.raws** (top and middle spectra in the leftmost (first) column) | ||
| Line 171: | Line 171: | ||
| * The two spectra in the fifth row corresponds to the MTDC summary spectra of OBJ-FP and XFP-FP ToFs (zoomed in). The spectra show the ToF (vertical axis) vs. hit number (horizontal axis). Note that in a unreacted-beam setting, the first hit typically provides the " | * The two spectra in the fifth row corresponds to the MTDC summary spectra of OBJ-FP and XFP-FP ToFs (zoomed in). The spectra show the ToF (vertical axis) vs. hit number (horizontal axis). Note that in a unreacted-beam setting, the first hit typically provides the " | ||
| * An empty ToF spectrum means that either the delays are not right (and need to be adjusted) or the spectrum range is too narrow | * An empty ToF spectrum means that either the delays are not right (and need to be adjusted) or the spectrum range is too narrow | ||
| - | * The MTDC spectra | + | * The MTDC delays |
| {{: | {{: | ||
| Line 177: | Line 177: | ||
| * Due to the multi-hit capability of the MTDC, we need to select the " | * Due to the multi-hit capability of the MTDC, we need to select the " | ||
| * Use the spectra **TOF.MTDC_RF**, | * Use the spectra **TOF.MTDC_RF**, | ||
| - | * Using the cursor mouse, check the lower and higher limits defining the region in the MTDC ToF spectra with the " | + | * Using the cursor mouse, check the lower and higher limits defining the region in the MTDC ToF spectra with the " |
| * Go to the **Variables** page in SpecTcl GUI and assign the limits to the following variables: | * Go to the **Variables** page in SpecTcl GUI and assign the limits to the following variables: | ||
| - | * s800.fp.vmetdc.mtdc_objlow | + | |
| - | * s800.fp.vmetdc.mtdc_objlow and s800.fp.vmetdc.mtdc_rfhigh | + | |
| - | * s800.fp.vmetdc.mtdc_xfplow and s800.fp.vmetdc.mtdc_xfphigh for XFP-XFP | + | |
| * For each ToF, SpecTcl will search the hit number that fits in the selected region. The new MTDC ToF parameters are **s800.fp.vmetdc.mtdc_rf**, | * For each ToF, SpecTcl will search the hit number that fits in the selected region. The new MTDC ToF parameters are **s800.fp.vmetdc.mtdc_rf**, | ||
| - | * If necessary, adjust delays: | + | * If necessary, adjust delays |
| - | * Using the [[S800 DAQ tools# | + | * Using the [[S800 DAQ tools# |
| - | * Select | + | * Connect |
| - | * Adjust the TDC delays of OBJ and XFP using the delay boxes connected to the CANBERRA CFD 454 in data U6 | + | * Adjust the TDC delays of OBJ and/or XFP with respect to the TDC start, |
| - | * Adjust | + | * Be aware that the after adjusting OBJ and XFP delays |
| - | * In principle, | + | * Check the corresponding ToF spectra in SpecTcl |
| + | |||
| + | * Check the efficiencies of the Phillips TDC, TACs, and MTDC for the OBJ-FP and XFP-FP ToFs: | ||
| + | * Make a gate on spectrum **IC.SUM** selecting the region of interest, and call it " | ||
| + | * Looking at the ToF spectra gated on " | ||
| + | * The window file **S800_TOF_EFFICIENCY.win** includes all the spectra needed | ||
| ==== Checking Particle ID and rate at S800 FP ==== | ==== Checking Particle ID and rate at S800 FP ==== | ||
| - | * Select SpecTcl window **S800_PID.win** in directory **/ | + | * Select SpecTcl window **S800_PID.win** |
| * The three columns correspond to the PID determined with the **RF-FP** ToF (left), **OBJ-FP** (center), and **XFP-FP** (right) | * The three columns correspond to the PID determined with the **RF-FP** ToF (left), **OBJ-FP** (center), and **XFP-FP** (right) | ||
| * The first (top) row corresponds to PID spectra using the Phillips TDC | * The first (top) row corresponds to PID spectra using the Phillips TDC | ||
| Line 276: | Line 282: | ||
| * Set trigger to “s800 trigger” | * Set trigger to “s800 trigger” | ||
| - | * Ensure that the **[[s800 daq tools# | + | * Ensure that the **[[s800 daq tools# |
| * Under trigger tab select **s800 trigger** (which is E1 up by definition) | * Under trigger tab select **s800 trigger** (which is E1 up by definition) | ||
| * Deselect experiment trigger | * Deselect experiment trigger | ||
| * SAVE TO FILE | * SAVE TO FILE | ||
| - | * Stop and start **[[s800 daq tools#Run Control Window|RunControl]]** to assert new trigger condition | + | * Begin a new run on [[#Readout GUI|Readout GUI]] to assert new trigger condition |
| * Select **[[s800 SpecTcl|Spectcl]]** window **S800_DISPMATCH.win** | * Select **[[s800 SpecTcl|Spectcl]]** window **S800_DISPMATCH.win** | ||
| Line 330: | Line 336: | ||
| * What experimenters want (e.g., if they want singles, the cut has to be more restrictive to limit acquisition deadtime) | * What experimenters want (e.g., if they want singles, the cut has to be more restrictive to limit acquisition deadtime) | ||
| * Move blocker, decrease attenuator, repeat | * Move blocker, decrease attenuator, repeat | ||
| + | |||
| + | * If necessary, do the ToF corrections to improve the PID resolution (instructions [[During experiments# | ||
tuning_the_s800_xdt.txt · Last modified: 2023/09/22 15:15 by swartzj
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 4.0 International
