tuning_the_s800_xdt
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
tuning_the_s800_xdt [2015/10/29 13:23] pereira [Timing setup] |
tuning_the_s800_xdt [2015/10/29 13:25] pereira [Checking Particle ID and rate at S800 FP] |
||
|---|---|---|---|
| Line 74: | Line 74: | ||
| * End and Begin **[[s800 daq tools#Run Control Window|ReadoutGUI]]** to assert new trigger condition | * End and Begin **[[s800 daq tools#Run Control Window|ReadoutGUI]]** to assert new trigger condition | ||
| - | * Select **[[s800 SpecTcl|Spectcl]]** window **S800_SCINT.win** in directory **/ | + | * Select **[[s800 SpecTcl|Spectcl]]** window **S800_SCINT.win** in directory **/ |
| * Adjust **[[hv bias|bias]]** looking at 2D spectra **e1.deup_e1.dedown** (showing the parameters s800.fp.e1.de_down vs. s800.fp.e1.de_up) for the FP E1 scintillator | * Adjust **[[hv bias|bias]]** looking at 2D spectra **e1.deup_e1.dedown** (showing the parameters s800.fp.e1.de_down vs. s800.fp.e1.de_up) for the FP E1 scintillator | ||
| Line 94: | Line 94: | ||
| - | * Select **[[s800 SpecTcl|Spectcl]]** window **S800_IC.win** | + | * Select **[[s800 SpecTcl|Spectcl]]** window **S800_IC.win** |
| * Adjust pad gains | * Adjust pad gains | ||
| Line 127: | Line 126: | ||
| * Count rate is a little higher than on scintillator due to noise or thresholds | * Count rate is a little higher than on scintillator due to noise or thresholds | ||
| - | * Check **[[s800 SpecTcl|Spectcl]]** window **S800_CRDCS.win** in directory **/ | + | * Check **[[s800 SpecTcl|Spectcl]]** window **S800_CRDCS.win** (see figure below) to verify the good performance of the detectors. (The spectra for each CRDC can be checked separatelly in windows **s800_CRDC1.win** and **S800_CRDC2.win**) |
| * Spectra **crdc1.raws** and **crdc2.raws** (top and middle spectra in the leftmost (first) column) | * Spectra **crdc1.raws** and **crdc2.raws** (top and middle spectra in the leftmost (first) column) | ||
| Line 193: | Line 192: | ||
| ==== Checking Particle ID and rate at S800 FP ==== | ==== Checking Particle ID and rate at S800 FP ==== | ||
| - | * Select SpecTcl window **S800_PID.win** in directory **/ | + | * Select SpecTcl window **S800_PID.win** |
| * The three columns correspond to the PID determined with the **RF-FP** ToF (left), **OBJ-FP** (center), and **XFP-FP** (right) | * The three columns correspond to the PID determined with the **RF-FP** ToF (left), **OBJ-FP** (center), and **XFP-FP** (right) | ||
| * The first (top) row corresponds to PID spectra using the Phillips TDC | * The first (top) row corresponds to PID spectra using the Phillips TDC | ||
tuning_the_s800_xdt.txt · Last modified: 2023/09/22 15:15 by swartzj
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 4.0 International
