User Tools

Site Tools


detectors

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
detectors [2017/06/19 18:21]
pereira [Ionization chamber]
detectors [2018/02/15 12:44] (current)
pereira [Cathode Readout Drift Chambers (CRDC)]
Line 27: Line 27:
  
 ===== Cathode Readout Drift Chambers (CRDC) ===== ===== Cathode Readout Drift Chambers (CRDC) =====
-Two Cathode Readout Drift Chamber (CRDC) are used  to measure the transversal positions and angles in  the [[Stations#​Focal Plane station|focal plane]]. The first detector (CRDC1) is located at the nominal optical focal plane, and it is separated 1 m from the second downstream detector (CRDC2). ​ Each detector has an active depth of 1.5 cm, an active area of 26 cm (non-dispersive direction) x 56 cm (dispersive direction), and [[Gas handling system|it is filled]] with a gas mixture consisting of 80% CF<​sub>​4</​sub>​ and 20% C<​sub>​4</​sub>​H<​sub>​10</​sub>​ at a typical pressure of 40 torr. The [[HV bias#​CRDCs|operating high power]] depends on the charge of the measured nuclei. A schematic view of a CRDC can be seen in the figure below.+Two Cathode Readout Drift Chamber (CRDC) are used  to measure the transversal positions and angles in  the [[Stations#​Focal Plane station|focal plane]]. The first detector (CRDC1) is located at the nominal optical focal plane, and it is separated 1 m from the second downstream detector (CRDC2). ​ Each detector has an active depth of 1.5 cm, an active area of 26 cm (non-dispersive direction) x 56 cm (dispersive direction), and [[Gas handling system|it is filled]] with a gas mixture consisting of 80% CF<​sub>​4</​sub>​ and 20% C<​sub>​4</​sub>​H<​sub>​10</​sub>​ at a typical pressure of 40 torr. The detector frame has a volume of 68 cm (dispersive) x 38 cm (non-dispersive) x 10.3 cm (depth). The [[HV bias#​CRDCs|operating high power]] depends on the charge of the measured nuclei. A schematic view of a CRDC can be seen in the figure below.
  
 {{:​wiki:​crdc-drawing.jpg?​600|Schematic view of the two S800 CRDCs.}} {{:​wiki:​crdc-drawing.jpg?​600|Schematic view of the two S800 CRDCs.}}
Line 52: Line 52:
  
 ===== Ionization chamber ===== ===== Ionization chamber =====
-An ionization chamber downstream of both [[Detectors#​Cathode Readout Drift Chambers (CRDC)|CRDCs]] is used to identify the Z number of the transmitted nuclei from their energy loss. The detector has an active area of __xxx cm x xxx cm and a depth of approximately 406 mm (16 inches). It [[Gas handling system||is filled]] with P10 gas (90% argon, 10% methane) at a typical pressure of 300 torr, although this value can be increased up to 600 torr for light nuclei. The detector consists of 16 stacked-parallel plate ion chambers with narrow anode-cathode gaps, placed along the detector’s central axis, perpendicular to the beam direction (see figure). The plates are constructed from 70 mg/​cm<​sup>​2</​sup>​ polypropylene with 0.05 µm of aluminum evaporated on each side. The entrance and exit windows of the chamber are made of 14 mg/​cm<​sup>​2</​sup>​ Mylar with an overlay of Kevlar filaments and epoxy.+An ionization chamber downstream of both [[Detectors#​Cathode Readout Drift Chambers (CRDC)|CRDCs]] is used to identify the Z number of the transmitted nuclei from their energy loss. The detector has an active area of __xxx cm x xxx cm__ and a depth of approximately 406 mm (16 inches). It [[Gas handling system||is filled]] with P10 gas (90% argon, 10% methane) at a typical pressure of 300 torr, although this value can be increased up to 600 torr for light nuclei. The detector consists of 16 stacked-parallel plate ion chambers with narrow anode-cathode gaps, placed along the detector’s central axis, perpendicular to the beam direction (see figure). The plates are constructed from 70 mg/​cm<​sup>​2</​sup>​ polypropylene with 0.05 µm of aluminum evaporated on each side. The entrance and exit windows of the chamber are made of 14 mg/​cm<​sup>​2</​sup>​ Mylar with an overlay of Kevlar filaments and epoxy.
 {{:​wiki:​ion-chamber-picture.jpg?​500 |Picture of the S800 ionization chamber with its alternating cathode and anode plates.}} {{:​wiki:​ion-chamber-picture.jpg?​500 |Picture of the S800 ionization chamber with its alternating cathode and anode plates.}}
 The electrons and positive ions liberated by the ionization of the gas along the particle trajectory drift towards the closest ​ anode-cathode pair. The drifting electrons and ions absorb the energy stored in the detector capacity and produce a voltage change of the anodes across the resistor. The main advantages of the anode-cathode configuration is that the electrons and ions are collected on a very short distance (about 1.5 cm), thus reducing pile-up and position dependence of the signals. Moreover, dividing the detector into 16 sections reduces the detector capacitance and consequently its noise. The operating voltage depends on the charge of the measured nuclei (e.g. __xxx for xxx and xxx for xxx__). Each anode is attached to a small preamplifier inside the ion chamber. This significantly reduces the electronic noise, although it involves the venting of the whole chamber whenever a malfunctioning preamplifier needs to be replaced. The electronic signals from the preamplifier are sent into a [[https://​groups.nscl.msu.edu/​nscl_library/​manuals/​caen/​MOD.N568B.pdf|CAEN N568B]] 16-channel shaper/​amplifier with remotely adjustable gains. The output signals feed a [[https://​groups.nscl.msu.edu/​nscl_library/​manuals/​phillips/​7164H.pdf|Phillips 7164H]] ADC.  The electrons and positive ions liberated by the ionization of the gas along the particle trajectory drift towards the closest ​ anode-cathode pair. The drifting electrons and ions absorb the energy stored in the detector capacity and produce a voltage change of the anodes across the resistor. The main advantages of the anode-cathode configuration is that the electrons and ions are collected on a very short distance (about 1.5 cm), thus reducing pile-up and position dependence of the signals. Moreover, dividing the detector into 16 sections reduces the detector capacitance and consequently its noise. The operating voltage depends on the charge of the measured nuclei (e.g. __xxx for xxx and xxx for xxx__). Each anode is attached to a small preamplifier inside the ion chamber. This significantly reduces the electronic noise, although it involves the venting of the whole chamber whenever a malfunctioning preamplifier needs to be replaced. The electronic signals from the preamplifier are sent into a [[https://​groups.nscl.msu.edu/​nscl_library/​manuals/​caen/​MOD.N568B.pdf|CAEN N568B]] 16-channel shaper/​amplifier with remotely adjustable gains. The output signals feed a [[https://​groups.nscl.msu.edu/​nscl_library/​manuals/​phillips/​7164H.pdf|Phillips 7164H]] ADC. 
detectors.1497910914.txt.gz · Last modified: 2017/06/19 18:21 by pereira