during_experiments
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
during_experiments [2015/10/29 14:13] pereira [Particle identification corrections] |
during_experiments [2017/06/17 14:54] pereira [Efficiency of OBJ Scintillator] |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== During experiment ====== | ====== During experiment ====== | ||
| This section describes support tasks that are typically requested during the course of an experiment. Some of them, like Mask calibration, | This section describes support tasks that are typically requested during the course of an experiment. Some of them, like Mask calibration, | ||
| + | |||
| + | * [[#Mask calibration]] | ||
| + | * [[#Particle identification corrections]] | ||
| + | * [[# | ||
| + | |||
| Line 81: | Line 86: | ||
| * The correction process described above can be used for other ToF. SpecTcl includes a set of corrected ToF parameters and variables for the OBJ-FP and XFP-FP ToFs taken from the Phillips TDC, TACs, and MTDC: | * The correction process described above can be used for other ToF. SpecTcl includes a set of corrected ToF parameters and variables for the OBJ-FP and XFP-FP ToFs taken from the Phillips TDC, TACs, and MTDC: | ||
| - | * s800.tof.objcorr1, | + | * **s800.tof.objcorr1**, **s800.tof.obj1Correction1**, **s800.tof.obj1Correction2**: Corrected parameter and correction variables for the OBJ-FP ToF taken from the Phillips TDC |
| - | * s800.tof.objcorr2, | + | * **s800.tof.objcorr2**, **s800.tof.obj2Correction1**, **s800.tof.obj2Correction2**: Corrected parameter and correction variables for the OBJ-FP ToF taken from the ORTEC TAC |
| - | * s800.tof.objcorr3, | + | * **s800.tof.objcorr3**, **s800.tof.obj3Correction1**, **s800.tof.obj3Correction2**: Corrected parameter and correction variables for the OBJ-FP ToF taken from the MTDC |
| - | * s800.tof.xfpcorr1, | + | * **s800.tof.xfpcorr1**, **s800.tof.xfp1Correction1**, **s800.tof.xfp1Correction2**: Corrected parameter and correction variables for the XFP-FP ToF taken from the Phillips TDC |
| - | * s800.tof.xfpcorr2, | + | * **s800.tof.xfpcorr2**, **s800.tof.xfp2Correction1**, **s800.tof.xfp2Correction2**: Corrected parameter and correction variables for the XFP-FP ToF taken from the ORTEC TAC |
| - | * s800.tof.xfpcorr3, | + | * **s800.tof.xfpcorr3**, **s800.tof.xfp3Correction1**, **s800.tof.xfp3Correction2**: Corrected parameter and correction variables for the XFP-FP ToF taken from the MTDC |
| + | |||
| + | |||
| + | |||
| + | ===== Efficiency of OBJ Scintillator ===== | ||
| + | At relatively high rates (~0.5 MHz), the OBJ scintillator will be gradually damaged. Experimenters should check the efficiency of this detector continuously during the course of the experiment. Whenever the rates drop below ~90%, they may request the Device/Beam Physicist to shim the detector. | ||
| + | Before shimming, make sure that the thresholds are set properly (not too high) (refer to section " | ||
| - | ===== Handling detectors ===== | ||
| ==== Shimming OBJ scintillator ==== | ==== Shimming OBJ scintillator ==== | ||
during_experiments.txt · Last modified: 2023/07/20 10:43 by swartzj
Page Tools
Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 4.0 International
