S800 Documentation

User Tools

Site Tools

Trace:
s800_daq_tools

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
Next revision Both sides next revision
s800_daq_tools [2020/03/05 12:23]
pereira [No data sources defined] 		s800_daq_tools [2020/03/05 12:27]
pereira [Mesytec CFD GUI]
Line 47: Line 47:
  
  
-  * To load the default CFD configuration go to **Load Setting**, select file **MCFD16.tcl** in directory **/user/operations/daq/usb/Config**, and click **Load**+  * To load the default CFD configuration go to **Load Setting**, select file **MCFD16.tcl** in directory **/user/s800/s800daq/Configurations**, and click **Load**
    * Alternatively, it is possible to load the configuration directly from the module by clicking **Update from Device**.     * Alternatively, it is possible to load the configuration directly from the module by clicking **Update from Device**. 
    * By default, the CFD parameters can be adjusted individually for each of the 16 channels. It is also possible use the module in a "common" mode to set the same CFD parameters to all channels. Just check **common**    * By default, the CFD parameters can be adjusted individually for each of the 16 channels. It is also possible use the module in a "common" mode to set the same CFD parameters to all channels. Just check **common**
Line 53: Line 53:
   * Don't forget to save the new settings in file **MCF16.tcl**.    * Don't forget to save the new settings in file **MCF16.tcl**. 
      - Go to ''File''      - Go to ''File''
-     - Click ''Browse'' and select directory **/user/operations/daq/usb/Config** (default)+     - Click ''Browse'' and select directory **/user/s800/s800daq/Configurations** (default)
      - Select file **MCFD16tcl** and click ''Save''      - Select file **MCFD16tcl** and click ''Save''
      - A warning window will pop out to verify that you want to overwrite the existing file. Answer ''Yes''      - A warning window will pop out to verify that you want to overwrite the existing file. Answer ''Yes''
Line 152: Line 152:
       - Go to **/mnt/events/operations/s800/exxxxlast**, where **exxxxlast** corresponds to the experiment number of the last (successfully) run experiment       - Go to **/mnt/events/operations/s800/exxxxlast**, where **exxxxlast** corresponds to the experiment number of the last (successfully) run experiment
       - Copy the file **.settings.tcl** from that directory to the current stagearea. **NOTE**: we are assuming that the stagearea is pointing to the new experiment directory **/mnt/events/operations/s800/exxxxlast**       - Copy the file **.settings.tcl** from that directory to the current stagearea. **NOTE**: we are assuming that the stagearea is pointing to the new experiment directory **/mnt/events/operations/s800/exxxxlast**
-      - If you cannot find that file, there is an old version that can be copied from the directory **/user/s800/cs800daq**+      - If you cannot find that file, there is an old version that can be copied from the directory **/user/s800/s800development/S800DAQ**
       - You should now be able to run ReadoutGUI without problem        - You should now be able to run ReadoutGUI without problem 
 ==== CCUSB and/or VMUSB claimed by existing programs ==== ==== CCUSB and/or VMUSB claimed by existing programs ====
s800_daq_tools.txt ยท Last modified: 2023/10/19 17:25 by swartzj

Page Tools

Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 4.0 International
CC Attribution-Noncommercial-Share Alike 4.0 International Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki