S800 Documentation

User Tools

Site Tools

Trace:
timing

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision 		Previous revision
Last revision Both sides next revision
timing [2016/07/24 17:41]
pereira 		timing [2020/04/02 20:54]
pereira [MTDC]
Line 4: Line 4:
 Although it is possible to measure the ToF between any pair of timing sources, there are three "standard" measurements provided to any experiment, namely, between the cyclotron and the S800 FP (RF-FP); between the A1900 FP and the S800 FP (XFP-FP); and between the S800 OBJ and FP (OBJ-FP). These ToFs are electronically recorded in a {{:wiki:Manual_Phillips_TDC_7186.pdf|Phillips 7186 TDC}}, a {{:wiki:MTDC-32.pdf|Mesytec TDC}} (MTDC), and a group of {{:wiki:Manual_Ortec_TAC_566.pdf|Ortec 566 TACs}}, all them located in the [[Electronics#Crate Configuration|electronic racks in S3]], near the FP box.  Although it is possible to measure the ToF between any pair of timing sources, there are three "standard" measurements provided to any experiment, namely, between the cyclotron and the S800 FP (RF-FP); between the A1900 FP and the S800 FP (XFP-FP); and between the S800 OBJ and FP (OBJ-FP). These ToFs are electronically recorded in a {{:wiki:Manual_Phillips_TDC_7186.pdf|Phillips 7186 TDC}}, a {{:wiki:MTDC-32.pdf|Mesytec TDC}} (MTDC), and a group of {{:wiki:Manual_Ortec_TAC_566.pdf|Ortec 566 TACs}}, all them located in the [[Electronics#Crate Configuration|electronic racks in S3]], near the FP box. 
  
-Although the timing reference ("start") in the all the ToF modules is given by the FP scintillator E1 up, the electronic path from the detector to each module is different (see {{:wiki:s800electronicstschematics-to20160720.pdf|main electronics diagram}} for more details). +Although the timing reference ("start") in the all the ToF modules is given by the FP scintillator E1 up, the electronic path from the detector to each module is different (see {{:wiki:s800electronicstschematics.pdf|main electronics diagram}} for more details). 
    
 Some important things to know about each of these modules: Some important things to know about each of these modules:
Line 16: Line 16:
   * The XFP detector signal is sent to a {{:wiki:Manual_Canberra_CFD_454.pdf|CANBERRA CFD 454 CFD}} in data U6 (patch panel #1 from data U1). The output from the CFD is then sent back to the MCFD in S3 via patch panel #70   * The XFP detector signal is sent to a {{:wiki:Manual_Canberra_CFD_454.pdf|CANBERRA CFD 454 CFD}} in data U6 (patch panel #1 from data U1). The output from the CFD is then sent back to the MCFD in S3 via patch panel #70
   * The MTDC timing signals do not require external delay adjustments because the matching window is sufficiently wide    * The MTDC timing signals do not require external delay adjustments because the matching window is sufficiently wide 
-  * The width and delay of the matching window can be changed in file **vmusbdaqconfig.tcl** in directory **/user/s800/converged_daq/Scripts**+  * The width and delay of the matching window can be changed in file **vmusbdaqconfig.tcl** in directory **/user/s800/s800daq/Scripts**
   * SpecTcl calculates the OBJ-FP and XFP-FP ToFs by substracting the E1 up time (MTDC channel 15) to the OBJ time (MTDC channel 3) and the XFP time (MTDC channel 2)    * SpecTcl calculates the OBJ-FP and XFP-FP ToFs by substracting the E1 up time (MTDC channel 15) to the OBJ time (MTDC channel 3) and the XFP time (MTDC channel 2) 
 +  * Note that the same flat ribbon cable connected to the MTDC is also feeding the scaler module. Thus, the 16 channels in the MTDC are exactly the same as channels 16-31 of the scaler module
 +  * Copies of the timing signals from XF and OBJ used for the TAC ToF were included in channels 8 and 9 of the MTDC (also the scaler) 
   * The table below lists the MTDC channels:      * The table below lists the MTDC channels:   
  
Line 29: Line 31:
 ^ CRDC1 Anode  ^ 6  |Tennelec Ampl. -> CANBERRA CFD -> ECL-NIM -> Fan in/out -> NIM-ECL| ^ CRDC1 Anode  ^ 6  |Tennelec Ampl. -> CANBERRA CFD -> ECL-NIM -> Fan in/out -> NIM-ECL|
 ^ CRDC2 Anode  ^ 7  |Tennelec Ampl. -> CANBERRA CFD -> ECL-NIM -> Fan in/out -> NIM-ECL| ^ CRDC2 Anode  ^ 7  |Tennelec Ampl. -> CANBERRA CFD -> ECL-NIM -> Fan in/out -> NIM-ECL|
-^ Free   ^ 8-11  | | +^ XFP   ^ 8  | Patch #1 (dU6) -> CANBERRA CFD (dU6) -> Patch #70 -> Fan in/out -> NIM-ECL| 
-^ Hodosc. OR ^ 12  |Leading edge -> ECL-NIM -> Fan in/out -> NIM-ECL|+^ OBJ   ^ 9  | Patch #54 (dU6) -> CANBERRA CFD (dU6) -> Patch #62 -> Fan in/out -> NIM-ECL | 
 +^ Free   ^ 10-11  | | 
 +^ Hodosc. OR ^ 12  | Splitter att. -> CANBERRA CFD -> Fan in/out -> NIM-ECL|
 ^ Free   ^ 13, 14  |  ^ Free   ^ 13, 14  | 
 ^ E1 up ^ 14  | LeCroy Var. ampl. -> Mesytec MCFD ch #0  -> ECL-NIM -> Fan in/out -> Fan in/out -> Fan in/out -> NIM-ECL | ^ E1 up ^ 14  | LeCroy Var. ampl. -> Mesytec MCFD ch #0  -> ECL-NIM -> Fan in/out -> Fan in/out -> Fan in/out -> NIM-ECL |
 ^ E1 up ^ 15  | LeCroy Var. ampl. -> Mesytec MCFD ch #0  -> ECL-NIM -> Fan in/out -> Fan in/out -> NIM-ECL | ^ E1 up ^ 15  | LeCroy Var. ampl. -> Mesytec MCFD ch #0  -> ECL-NIM -> Fan in/out -> Fan in/out -> NIM-ECL |
 +^ II PPAC2 anode  ^ 16  | Mesytec MCFD2 ch #0 |
 +^ II PPAC2 down  ^ 17  | Mesytec MCFD2 ch #1 |
 +^ II PPAC2 up  ^ 18  | Mesytec MCFD2 ch #2 |
 +^ II PPAC2 right  ^ 19  | Mesytec MCFD2 ch #3 |
 +^ II PPAC2 left  ^ 20  | Mesytec MCFD2 ch #4 |
 +^ II PPAC1 anode  ^ 21 | Mesytec MCFD2 ch #5 |
 +^ II PPAC1 down  ^ 22 | Mesytec MCFD2 ch #6 |
 +^ II PPAC1 up  ^ 23 | Mesytec MCFD2 ch #7 |
 +^ II PPAC1 right  ^ 24 | Mesytec MCFD2 ch #8 |
 +^ II PPAC1 left  ^ 25 | Mesytec MCFD2 ch #9 |
 +
  
 The multi-hit capability requires some special attention. Let's imagine a situation where the rate from OBJ detector is much higher than from the FP detector. During this window, the MTDC will record one hit from the FP scintillator (E1 up, which SpecTcl uses as the start ToF reference) and multiple hits from the OBJ scintillator (stops). As a results, SpecTcl will generate an array of OBJ-FP ToFs  called **s800.fp.vmetdc.obj.i**, where i=0 stands for the first hit, i=2 second hit and so on (the corresponding array for XFP-FP TOF is **s800.fp.vmetdc.xfp.i**). The multi-hit capability requires some special attention. Let's imagine a situation where the rate from OBJ detector is much higher than from the FP detector. During this window, the MTDC will record one hit from the FP scintillator (E1 up, which SpecTcl uses as the start ToF reference) and multiple hits from the OBJ scintillator (stops). As a results, SpecTcl will generate an array of OBJ-FP ToFs  called **s800.fp.vmetdc.obj.i**, where i=0 stands for the first hit, i=2 second hit and so on (the corresponding array for XFP-FP TOF is **s800.fp.vmetdc.xfp.i**).
Line 58: Line 73:
 ^  Signal  ^  Ch. ID  ^ Electronic path (from detector) | ^  Signal  ^  Ch. ID  ^ Electronic path (from detector) |
 ^  S800 trigger  ^  start  |LeCroy Var. ampl. -> Mesytec MCFD ch #0  -> ECL-NIM -> 4x Fan in/out -> Logic Unit-> 300 ns delay| ^  S800 trigger  ^  start  |LeCroy Var. ampl. -> Mesytec MCFD ch #0  -> ECL-NIM -> 4x Fan in/out -> Logic Unit-> 300 ns delay|
-^  OBJ  ^  stop  | Patch #54 (dU6) -> CANBERRA CFD (dU6) -> Patch #62  |+^  OBJ  ^  stop  | Patch #54 (dU6) -> CANBERRA CFD (dU6) -> Patch #62 -> Fan in/out |
  
   * The table below lists the XFP-FP TAC channels:     * The table below lists the XFP-FP TAC channels:  
Line 68: Line 83:
  
 ==== Phillips TDC ==== ==== Phillips TDC ====
 +**ATTENTION: Since the end of the GRETINA-2017 campaign, this module is no longer used**
 +
   * Before going to the TDC, the OBJ and XFP detector signals are sent to a {{:wiki:Manual_Canberra_CFD_454.pdf|CANBERRA CFD 454 CFD}} in data U6 via patch panel #54 and #1, respectively   * Before going to the TDC, the OBJ and XFP detector signals are sent to a {{:wiki:Manual_Canberra_CFD_454.pdf|CANBERRA CFD 454 CFD}} in data U6 via patch panel #54 and #1, respectively
   * The TDC start is provided by the [[Trigger|ULM trigger module]]. Since the delay of the S800 trigger may be adjusted during tuning of the S800 (XDT), the stop signals (e.g. from OBJ or XFP) need to be re-adjusted so that the ToF fits into the 400-ns range of the TDC. This is done manually for OBJ and XFP, and remotely via [[XLM Delay|XLM delay module]] (operated by the [[S800 DAQ tools#Delay Window|Delay GUI]]) for other timing signals    * The TDC start is provided by the [[Trigger|ULM trigger module]]. Since the delay of the S800 trigger may be adjusted during tuning of the S800 (XDT), the stop signals (e.g. from OBJ or XFP) need to be re-adjusted so that the ToF fits into the 400-ns range of the TDC. This is done manually for OBJ and XFP, and remotely via [[XLM Delay|XLM delay module]] (operated by the [[S800 DAQ tools#Delay Window|Delay GUI]]) for other timing signals 
timing.txt · Last modified: 2020/04/02 20:58 by pereira

Page Tools

Except where otherwise noted, content on this wiki is licensed under the following license: CC Attribution-Noncommercial-Share Alike 4.0 International
CC Attribution-Noncommercial-Share Alike 4.0 International Donate Powered by PHP Valid HTML5 Valid CSS Driven by DokuWiki