User Tools

Site Tools


venting_pumping_intermediate_image_box

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Last revision Both sides next revision
venting_pumping_intermediate_image_box [2018/12/19 11:42]
pereira [Venting/pumping Intermediate Image box and filling PPACs with gas]
venting_pumping_intermediate_image_box [2018/12/20 15:16]
pereira [Removing gas from Intermediate-image delay PPAC]
Line 78: Line 78:
  
 Requirements:​ PanelMate files **S3_Gas_Handling** and **S800Vac** Requirements:​ PanelMate files **S3_Gas_Handling** and **S800Vac**
 +
 +==== Filling Intermediate-image delay PPAC with gas ====
   * Verify that PPACs are not biased:   * Verify that PPACs are not biased:
         * Check that the detectors are unbiased by opening the [[HV bias|HV GUI]]         * Check that the detectors are unbiased by opening the [[HV bias|HV GUI]]
         * Notify the system of the bias-off state by selecting the "​I214BON_CONFIRM"​ box in **S3_Gas_Handling** and clicking "PP BIAS OFF CONFIRMED"​         * Notify the system of the bias-off state by selecting the "​I214BON_CONFIRM"​ box in **S3_Gas_Handling** and clicking "PP BIAS OFF CONFIRMED"​
 +  * Verify that ion gauge I213IG is off
   * Verify that PPACs are in automatic mode with gas removed (**S3_Gas_Handling**)   * Verify that PPACs are in automatic mode with gas removed (**S3_Gas_Handling**)
         * The "GH System Status box should read "Auto Mode Gas Removed"​         * The "GH System Status box should read "Auto Mode Gas Removed"​
-        * If gas is removed but the system is not in the automatic mode, consult the Beam Physicists or Device Physicist. This typically requires to verify that the system is in a controlled status. In particular, the "​I214BON_CONFIRM"​ box should indicate "PP BIAS OFF CONFIRMED",​ and the only that should be open in **S3_Gas_Handling** are the "Det Bypass"​ (V5) and "Chmbr Bypass"​ (V6); the rest of the valves (Gas Sup V1, Gas Lin Pmp Out V2, Flow Bypass V3, Det Return V4, and I214V_NCL (enable) should be closed+        * If gas is removed but the system is not in the automatic mode, consult the Beam Physicists or Device Physicist. This typically requires to verify that the system is in a controlled status. In particular, the "​I214BON_CONFIRM"​ box should indicate "PP BIAS OFF CONFIRMED",​ and the only valves ​that should be open in **S3_Gas_Handling** are the "Det Bypass"​ (V5) and "Chmbr Bypass"​ (V6); the rest of the valves (Gas Sup V1, Gas Lin Pmp Out V2, Flow Bypass V3, Det Return V4, and I214V_NCL (enable)) should be closed
   * Confirm that PanelMate box "​I214P_AUTO/​MAN Pre Set" reads 5 Torr (the set gas pressure in the detector) ​   * Confirm that PanelMate box "​I214P_AUTO/​MAN Pre Set" reads 5 Torr (the set gas pressure in the detector) ​
   * Open the gas bottle valve (sitting near the gas handling system)   * Open the gas bottle valve (sitting near the gas handling system)
Line 95: Line 98:
         * GH System status will indicate "Flow Estab."​         * GH System status will indicate "Flow Estab."​
         * I214BON_CONFIM will change to "PPAC BIAS ASSUMED ON"         * I214BON_CONFIM will change to "PPAC BIAS ASSUMED ON"
-        * The valves status will be: V1 (open), V2 (closed), V3 (closed), V4 (open), V5 (closed), V6 (closed, I214V_NCL (enabled)+        * The valves status will be: V1 (open), V2 (closed), V3 (closed), V4 (open), V5 (closed), V6 (closed), I214V_NCL (enabled)
         * You can now turn on the detectors         * You can now turn on the detectors
 +
 +
 +
 +
 +==== Removing gas from Intermediate-image delay PPAC ====
 +  * Verify that PPACs are not biased:
 +        * Check that the detectors are unbiased by opening the [[HV bias|HV GUI]]
 +        * Notify the system of the bias-off state by selecting the "​I214BON_CONFIRM"​ box in **S3_Gas_Handling** and clicking "PP BIAS OFF CONFIRMED"​
 +  * Verify that PPACs are in automatic mode with gas flowing (**S3_Gas_Handling**)
 +        * The "GH System Status box should read "Auto Gas Flow Estab"
 +        * If gas is flowing but the system is not in the automatic mode, consult the Beam Physicists or Device Physicist. This typically requires to verify that the system is in a controlled status. In particular, the "​I214BON_CONFIRM"​ box should indicate "PP BIAS OFF CONFIRMED",​ and the valves should indicate:
 +              * I214 Gas Sup V1 (open)
 +              * Gas Lin Pmp out V2 (closed)
 +              * Flow Bypass V3 (closed)
 +              * Det Return V4 (open)
 +              * Det Bypass V5 (closed)
 +              * Chmbr Bypass (closed)
 +              * I214V_NCL (enabled) ​
 +  * PanelMate box "Gas Removal Control"​ should indicate "OK to Start Gas Removal"​. Select that box and click on "Start Gas Removal"​
 +        * Valves V1 (I214 Gas Sup) and I214V_NCL will close 
 +        * Valves V3 (Flow Bypass) and Det Bypass (V5) will open
 +        * I214CM Press Rdg will gradually decrease to zero
 +        * GH System status should indicate "Gas Removal"​
 +  * When the gas is removed from the detector
 +        * Valve V3 (Flow Bypass) and 4 (Det return) will close
 +        * Valve V6 (Chamber Bypass) will open
 +        * GH System status will indicate "Gas Removed"​
 +        * I214BON_CONFIM will change to "PPAC BIAS ASSUMED ON"
 +        * The valves status will be: V1 (closed), V2 (closed), V3 (closed), V4 (closed), V5 (open), V6 (open), I214V_NCL (closed)
 +
 +
 +
venting_pumping_intermediate_image_box.txt ยท Last modified: 2019/02/13 09:40 by pereira