Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revision Both sides next revision | ||
|
fillsystem:alarmresponse [2013/05/07 14:26] weisshaa |
fillsystem:alarmresponse [2014/02/27 16:14] 127.0.0.1 external edit |
||
|---|---|---|---|
| Line 2: | Line 2: | ||
| You need to log on gln1, see [[LN computer]]. Go to directory ~/scripts and run ./run-gln-ui.sh which gives the fill system interface. | You need to log on gln1, see [[LN computer]]. Go to directory ~/scripts and run ./run-gln-ui.sh which gives the fill system interface. | ||
| - | Type help for getting overview on commands. Get familiar with the commands fill, clr, coff, con, abort, load, quit | + | Type help for getting overview on commands. Get familiar with the commands mon, clr, ton, fill, coff, con, abort, load, quit |
| In some cases you need to edit the fill-system configuration file ~/gln/gln.fig for setting new temperature thresholds. In order | In some cases you need to edit the fill-system configuration file ~/gln/gln.fig for setting new temperature thresholds. In order | ||
| Line 27: | Line 27: | ||
| * Run run-gln-ui.sh | * Run run-gln-ui.sh | ||
| * Say 'clr' to clear alarm | * Say 'clr' to clear alarm | ||
| - | * You need to re-enable filling of this detector | + | * You need to re-enable filling of this detector (ton #det) |
| * If this happens regularly you may want to increase the T high threshold in gln.fig (F3 directive, end in gln.fig) | * If this happens regularly you may want to increase the T high threshold in gln.fig (F3 directive, end in gln.fig) | ||
| Line 34: | Line 34: | ||
| * IMPORTANT: detector T increased by few Kelvin only, see example plot below. | * IMPORTANT: detector T increased by few Kelvin only, see example plot below. | ||
| * Run run-gln-ui.sh | * Run run-gln-ui.sh | ||
| - | * Say 'fill det#', confirm that you want to fill it. | + | * Say 'fill det#', confirm that you really want to fill it. |
| * Say 'coff det#', this stops T checking (and alarming and disabling) of this detector | * Say 'coff det#', this stops T checking (and alarming and disabling) of this detector | ||
| * Watch the fill, check for reasonable fill time (not that LN out is triggering much too early) | * Watch the fill, check for reasonable fill time (not that LN out is triggering much too early) | ||
| Line 40: | Line 40: | ||
| * If T is good say 'con #det', so T checking is enabled again. | * If T is good say 'con #det', so T checking is enabled again. | ||
| * If it is deep in the night: You can temporary increase T high threshold (F3 directive) | * If it is deep in the night: You can temporary increase T high threshold (F3 directive) | ||
| - | * NEVER LEAVE DETECTOR T CHECK OFF | + | * NEVER LEAVE DETECTOR T CHECKED OFF |
| Line 47: | Line 47: | ||
| {{:fillsystem:warm-up-example.pdf|}}. Actually after alarm you get it up to | {{:fillsystem:warm-up-example.pdf|}}. Actually after alarm you get it up to | ||
| channel ~1100 and see T is going up. Therefore it is a real alarm. Next you do | channel ~1100 and see T is going up. Therefore it is a real alarm. Next you do | ||
| - | is logging on the gln system, run the UI, and say fill 6. Then clr and directly | + | is logging on the gln system, run the UI, and say 'fill 6 now'. Then clr and directly |
| coff 6 (as a fill enables T checking by default). Later you see how T is recovering. | coff 6 (as a fill enables T checking by default). Later you see how T is recovering. | ||
| + | dirk cell:517 203 9419 | ||
