Differences
This shows you the differences between two versions of the page.
| Next revision | Previous revision Next revision Both sides next revision | ||
|
fillsystem:ln_computer [2012/05/11 20:21] weisshaa created |
fillsystem:ln_computer [2012/05/19 09:44] weisshaa [ADC to channel mapping] |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== Login on LN computer ====== | ====== Login on LN computer ====== | ||
| The LN computer lives in the GRETINA net and doesn't know | The LN computer lives in the GRETINA net and doesn't know | ||
| - | about the outside word. | + | about the outside world. |
| - | a2.gam (35.8.35.163) | + | * login on gateway machine nsclgw1.nscl.msu.edu |
| - | ln@gln1 (10.0.4.11) | + | * login as gretina on a2.gam (35.8.35.163) |
| - | lz=724g | + | * login as ln on gln1 (10.0.4.11) |
| - | ~/gln/gln.fig | + | ====== LN scripts ====== |
| + | They are found in ~/scripts. The main LN program (gln_master) is a job | ||
| + | run by root and not directly accessible by the user. Interactions happen | ||
| + | via scripts. Most interesting is //run-gln-ui.sh//, the User Interface. | ||
| + | ***run-gln-ui.sh**: User Interface, 'help' gives option | ||
| + | *run-send-alarm.sh: Add your email here for receiving alarms | ||
| + | *run-log.sh: Add your email here for receiving logs | ||
| + | *run-log2.sh: Add your email here for receiving logs after each fill | ||
| + | *run-log3.sh: | ||
| + | *run-send-alarm-wd.sh | ||
| + | *finish_fill.sh: script executed after fill attempt | ||
| + | *run-gln-master.sh | ||
| + | *run-mail-que-view.sh | ||
| + | *run-time-sync.sh | ||
| + | *run-backup.sh | ||
| + | *run-tlog-and-plot.sh | ||
| + | *run-dlog-and-plot.sh | ||
| + | *run-mail-que-flush.sh | ||
| + | *run-view-master.sh: Output of the LN master process | ||
| + | |||
| + | ====== LN configuration ====== | ||
| + | The LN configuration file is found as ~/gln/gln.fig. It is //self-explanatory//. If this file got updated, use run-gln-ui.sh script and the command "load" in there. Note: After a "load" in the UI all detector fill schedules are gone! You need to do a "fill x y z after h:mm". | ||
| + | |||
| + | ====== ADC to channel mapping ====== | ||
| + | Documentation for ADC mapping: {{:connections_1_.pdf|}} | ||
| + | |||
| + | * ADC 1-4: Manifold overflow 1-4 (Manifold overflow at supply box Q1-Q4) | ||
| + | * ADC 11-17: Fill overflow Q1-Q7 (Overflow input at supply box) | ||
| + | |||
| + | ^ Quad supply ^ LN ADC ^ LN ADC ^ PreAmp L ^ PreAmp H^ | ||
| + | ^ 1 | | | | | | ||
| + | ^ 2 | 45 | 46 | 48 | 47 | | ||
| + | ^ 3 | | | | | | ||
| + | ^ 4 | | | | | | ||
| + | ^ 5 | | | | | | ||
| + | ^ 6 | 30 | 62| 63 | 61 | | ||
| + | ^ 7 | 34 | 32 | 33 | 31 | | ||
| + | |||
| + | PreAmp L/H: preamplifier T reading lower/higher T | ||
