This is an old revision of the document!
- 152Eu source sheet z2707-1.pdf
validate: Channels which triggered get written
TTCS: All 40 channels of a triggering crystal get written
in Run directory, file Setpoints: CryG_CS_BRE is status of baseline restorer
Run lists:
| date | directory | run | Description |
|---|---|---|---|
| data1a/MSUJune2012 | 7 | 60Co, d/s 1, 8000Mb/sec, 18% DT | |
| 6/5/12 | data1a/MSUJune2012 | 10 | 5Mev range in mode 2+3, 60Co weak, d/s 10 |
| 12 | 5MeV range in mode 2+3, 152Eu at center, d/s 10, BLR off | ||
| 13 | 5MeV, mode 2+3, 152Eu center, d/s 5, BLR off | ||
| 14 | mode 3 validate, 0.2us trace, 152Eu center, d/s 10, BLR off | ||
| 15 | mode 3 validate, 0.2us trace, 152Eu center, d/s 10, BLR off, HEMIs closed! | ||
| 16 | mode 2+3, 152Eu center, d/s 10, BLR off, HEMIs closed! | ||
| 17 | mode 2+3, 60Co (weak) center, d/s 10, BLR off, HEMIs closed! | ||
| 23 | mode 3 validate, 0.2us, 60Co (weak) center, d/s 10, BLR off, HEMIs closed! | ||
| 24 | mode 3 validate, 0.2us, 60Co (weak) center, d/s 10, BLR off, HEMIs open! | ||
| 25 | mode 2+3, 60Co (weak) center, d/s 10, BLR off, HEMIs open! | ||
| 27 | mode 2+3, no source, d/s 1, BLR off, HEMIs closed! | ||
| 6/6/12 | data1a/MSUJune2012 | 28 | mode 2+3, no source, d/s 1, BLR off, HEMIs open! |
| FROM HERE ON S800 SYNCHRONIZATION SET UP WRONG (most likely) | |||
| 59 | mode 3 TTCS + LaBr, coinc or Gretina ds 50 or LaBr ds 20, most likely S800 did run with internal clock since then → no 'obvious' correlation | ||
| 60 | mode 3 TTCS + LaBr, coinc or Gretina ds 50 or LaBr ds 20 | ||
| 61 | mode 3 TTCS + LaBr, coinc or Gretina ds 50 or LaBr ds 20 | ||
| 62 | mode 3 TTCS + LaBr, coinc or Gretina ds 50 or LaBr ds 20 | ||
| 63 | mode 3 TTCS + LaBr, coinc or Gretina ds 50 or LaBr ds 20 | ||
| 65 | mode 3 TTCS + LaBr, coinc or Gretina ds 50 or LaBr ds 20 | ||
| 6/7/12 | data1a/MSUJune2012 | 67 | mode 3 TTCS + LaBr, coinc or Gretina ds 50 or LaBr ds 20 |
| 69 | mode 3 TTCS + LaBr, coinc or Gretina ds 50 or LaBr ds 20, fill during Run | ||
| 70 | mode 3 TTCS + LaBr, coinc or Gretina ds 50 or LaBr ds 20 | ||
| 71 | mode 3 TTCS + LaBr, coinc or Gretina ds 50 or LaBr ds 20 | ||
| 72 | mode 3 TTCS + LaBr, coinc or Gretina ds 50 or LaBr ds 20 | ||
| 6/8/12 | data1a/MSUJune2012 | 73 | mode 3 TTCS + LaBr, coinc or Gretina ds 50 or LaBr ds 20 |
| 108 | mode 2only Decomp 1-28, sendRaw 29 (TTCS) for LaBr, or Gretina | ||
| 110 | mode 2only Decomp 1-28, sendRaw 29 (TTCS) for LaBr, coinc or Gretina ds 50 or LaBr ds 20 | ||
| HERE WE SET THE S800 SYNCHRONIZATION CHECK BUTTON PROPERLY | |||
| 130 | mode 3 TTCS + LaBr, coinc or Gretina ds 50 or LaBr ds 20 | ||
| 6/9/12 | data1a/MSUJune2012 | 162 | mode 3 TTCS, or Gretina with ~ 1 MeV threshold, “Super Pulse” measurement, IOC of CRY#7 failed after 2 hours |
| 6/10/12 | data1a/MSUJune2012 | 165 | mode 3 TTCS, or Gretina with ~ 1 MeV threshold, “Super Pulse” measurement, CRY#7 only |
| QUADS MOVED TO THE FINAL CONFIGURATION. Q2 and Q5 are not swapped any more | |||
| 6/13/12 | data1x/MSUJune2012 | 171 | mode 3 Validate 0.2 us 60Co only Q1 Q2 Q3 with old positions |
| IOCs and decomps configured for the new position | |||
| 6/14/12 | data1x/MSUJune2012 | 184 | mode 3 Validate 0.2 us 60Co with new positions |
| data1x/MSUJune2012 | 203 | mode 3 Validate 0.2 us 60Co 37GB – BLR on – analysis bug | |
| 6/15/12 | data1x/MSUJune2012 | 204 | mode 3 Validate 0.2 us 60Co 37GB – BLR off |
| data1x/MSUJune2012 | 211 | mode 3 Validate 0.2 us 60Co 37GB – BLR on (readout_limit 2000) – scrap | |
| data1x/MSUJune2012 | 240 | mode 3 Validate 0.2 us 60Co 37GB – BLR on (readout_limit 500) | |
| 6/17/12 | data1x/MSUJune2012 | 252 | mode 3 Validate 0.2 us 60Co 15min – readout_limit 100 (500) |
| data1x/MSUJune2012 | 253 | mode 3 Validate 0.2 us 60Co 15min – readout_limit 200 (500) | |
| data1x/MSUJune2012 | 254 | mode 3 Validate 0.2 us 60Co 15min – readout_limit 300 (500) | |
| data1x/MSUJune2012 | 255 | mode 3 Validate 0.2 us 60Co 15min – readout_limit 500 | |
| data1x/MSUJune2012 | 256 | mode 3 Validate 0.2 us 60Co 15min – readout_limit 700 | |
| data1x/MSUJune2012 | 257 | mode 3 Validate 0.2 us 60Co 15min – readout_limit 1000 | |
| data1x/MSUJune2012 | 258 | mode 3 Validate 0.2 us 60Co 15min – readout_limit 1500 | |
| data1x/MSUJune2012 | 261 | mode 3 Validate 0.2 us 60Co 15min – readout_limit 2000 | |
| data1x/MSUJune2012 | 270 | mode 3 TTCS 2 us 60Co 15min – readout_limit 500 | |
| data1x/MSUJune2012 | 271 | mode 3 TTCS 2 us 60Co 15min – readout_limit 2000 | |
| swap found in Q7P2 between signal cable 3 and 4 – fixed | |||
| 6/18/12 | data1x/MSUJune2012 | 298 | mode 3 Validate 60Co Q2 and Q5 – 20us |
| 6/19/12 | data1x/MSUJune2012 | 308 | mode 3 Validate 0.2 us 60Co – Q2 in rotated position → good resolution but P3a3 |
| data1x/MSUJune2012 | 315 | mode 3 Validate 0.2 us 60Co – Q6P2 fixed | |
| 6/20/12 | data1x/MSUJune2012 | 341 | mode 3 Validate 0.2 us 60Co – test of North hemi - Q2P3a3 to be fixed |
| data1x/MSUJune2012 | 344 | mode 3 Validate 0.2 us 60Co – calibration run 45min - check of north hemi | |
| data1x/MSUJune2012 | 345 | mode 3 Validate 0.2 us 60Co – calibration run - check of north hemi | |
| data1x/MSUJune2012 | 346 | mode 3 Validate 0.2 us background run - checking dynamic range | |
| 6/21/12 | data1x/MSUJune2012 | 383 | mode 3 Validate 0.2 us 60Co – calibration of North hemisphere |
| changed ID position for the detectors | |||
| 6/21-22/12 | data1x/MSUJune2012 | 401 | mode 2 TTCS 2 us 60Co – test of decomposition for northern hemi |
| data1x/MSUJune2012 | 404 | validate mode 0.2us 60Co – test of northern hemi again | |
| data1x/MSUJune2012 | 405 | validate mode 0.2us 60Co – calibration of the southern hemi | |
| data1x/MSUJune2012 | 408 | mode 2 - 2us 60Co – Southern hemi - test of calib 1 | |
| data1x/MSUJune2012 | 409 | mode 2 - 2us 60Co – Southern hemi - test of calib 1 | |
| New directory in use: /global/data1x/gretina/MSUTestBeam_June2012 | |||
| data1x/MSUTestBeam_June2012 | 6 | mode 2 TTCS - 2us Background – Full Gretina |
