This is an old revision of the document!
This page gives user-level instructions on how to run the S800 data acquisition (DAQ) system for an experiment. Presently this is run from the linux machine u6pc5 in data-U6.
The S800 Readout GUI is invoked by either clicking the icon S800 DAQ in the desktop of u6pc5 or by navigating in a Linux terminal to the directory /user/s800/converged_daq and typing
godaq. The Readout GUI window will appear with three tags labeled “main”, “SSHPipe@localhost:0”, and “SSHPipe@localhost:1”. The first one provides general information about the ReadoutGUI. The second and third tabs provide information about the data sources (from the CCUSB and VMUSB controllers). IMPORTANT NOTE: When running Readout GUI, make sure that the environment variables needed by the system are properly defined. This can be done from a Linux session connected to spdaq19 by typing:
. /usr/opt/nscldaq/xxxx/daqsetup.bash, where
xxxx is the nscldaq version (xxx = 11.0-020, on Feb 2016).
Before beginning taking data is necessary to initialize the system. This is done by clicking
Start in the ReadoutGUI. You can inspect the status of each source during their initialization by clicking in one of the tabs “SSHPipe@localhost:0” or “SSHPipe@localhost:1”. You will see a series of messages about the different initialization steps. The last message should be “Done”. During the initialization process, a fourth tab labeled “ActionFilter” may appear with information from the S800 filter. Sometimes, you may see a warning message about an old “still-running” S800 filter session being killed. That's ok.
After initializing the contollers, the ReadoutGUI window will show the
Begin button active. In addition, three additional buttons should appear at the end of the window. They can be used to start the GUI associated with the MCFD, Delay XLM, and Trigger ULM modules. Make sure that the system is completely initializing before opening those GUIs.
The figure below shows the Readout GUI window after initializing the system. After clicking
Begin, the “Event Builder” window will pop out, displaying information about the Readout session. (Note that the tab “ActionFilter” may appear if it didn't show up before, when you clicked
Start.) Data can be recorded on disk by checking out the box
Record. To end a data run, simply click
The S800 electronics includes a Mesytec CFD (MCFD), used to “filter” the detector signals going to the Scaler and Mesytec TDC. The configuration parameters of the CFD (thresholds, delays, fraction, etc.) can be remotely adjusted via a MCFD GUI developed by the NSCL DAQ group. During tuning of the S800, one typically needs to adjust thresholds only.
The MCFD GUI can be started in three different ways: 1) by clicking the button
Launch MCFD GUI in Readout GUI; 2) by clicking the icon MCFD GUI in the desktop of u6pc5; 3) by navigating in a Linux terminal and typing
$DAQBIN/MCFDControl16 –protocol usb –serialfile /dev/ttyUSB0. The environment variable DAQBIN is defined by sourcing the daqsetup.bash file in directory /usr/opt/nscldaq/xxxx/bin, where xxxx is the nscldaq version number (11.0-015 on Oct 26, 2015).
Browseand select directory /user/operations/daq/usb/Config (default)
Backto return to the main GUI
This window appears when the “Launch Gate Delay GUI” button is pressed on the Readout GUI. The delay module allows software configurable delays to be applied to each of the signals indicated in the Channel column, which then form the TDC stops. It is configurable to enable delays to be set with beam on target, as the needed delay may change depending on experimental conditions.
Some important things to remember:
The Trigger GUI appears when the “Launch ULM GUI” button is pressed on Readout GUI. The Trigger GUI is a visual display of the various Gate and Delay Generators and logic elements that make up the configurable trigger of the S800. The logic of the trigger decision is readily discerned from a visual inspection of this GUI. Setting the trigger configuration is also done using this GUI
The different signal going through the trigger scheme can be inspected in th Data-U6 oscilloscope. Simply right click on any of the wires to put that signal onto one of the four “Trigger Inspect” channels available at the patch panel of Data-U6, and connect that patch-panel cable to the oscilloscope. By inspecting the various delays, widths and overlaps the user trigger can be configured. The Trigger GUI is discussed in greater detail here.
The GUI used to display scalers rates can be open from the icon S800 Scalers in the desktop of u6pc5. Alternatively, open a terminal on u6pc5, and type ./goscalers from directory /user/s800/converged_daq/scalers.
The GUI includes two pages labeled “s800” and “ratios”. Page “s800” includes all the scaler channels; page “ratios” displays ratio values calculated between several pairs of channels. In addition, the GUI includes a panel showing the time evolution of the live time calculated from the live-to-raw trigger ratio, and the live-to-raw clock ratio. The figure below shows the page “ratios” from the scaler GUI.
A list of scaler channels can be found here.
The S800 DAQ can be run in Standalone mode (as described above), or in Slave mode. The later means that the S800 DAQ is controlled by an external DAQ (e.g. GRETINA). In this mode, the S800 ULM receives an external clock signal and external synchronization from the master DAQ. Running in Slave mode requires to change the script CC0105Begin.tcl in directory /user/s800/converged_daq/Scripts. In this file, there are two variables
extclock to define if the external synchronization and clock signals are enabled (=1) or disabled (=0). Make sure that you set these variables to 1 if you want to run in Slave mode.
One of the
There are several common reasons why the S800 DAQ may fails to start. The list below describes what to do to fix these problems.
Sometimes, particularly if the previous S800 DAQ session ended in an uncontrolled way, there may be old processes running (CCUSB and/or VMUSB and/or S800 event builder) that will prevent Readout GUI to begin a run. Whenever this happens (typically after clicking
Begin in Readout GUI), the system sends an error message complaining about one of these processes still running. If you find yourself in this situation try:
ssh -Y s800@spdaq19(the S800 password can be found in the S800 binder that is kept in the data-U1 logbook cabinet)
ps aux | grep Readoutto ensure that Readout is indeed not running
/usr/opt/nscldaq/xxxx/bin/ringbuffer status, where xxxx is the daq version, e.g. 11.0-020
producer) is -1. (Don't worry about the ringbuffer s800filter, which is automatically killed when starting ReadoutGUI)
kill -9 PID
Begin in the S800 Readout GUI, you get the error message: “No data sources are running so a run cannot be started”. Very likely, the setting file .settings.tcl is missing. On a Linux session in u6pc5, type
ls -lisa ~/stagearea. You should see a hidden file .settings.tcl. If no, try the following:
One of the most common reasons why the S800 DAQ fails to start is because the CCUSB and/or VMUSB are claimed by existing programs. This is shown by the error messages displayed by the system. If you find yourself in this situation try the following:
ps aux | grep Readout
kill -9 PID, where PID identifies any CCUSBReadout or VMUSBReadout processes that show up
kill -9 PID, where PID identifies any tclsh ReadoutShell process that might show up
godaqto see if this works now
In the rare case that the RunControl GUI gets “frozen”, it is possible to reboot the whole system manually. This operation requires to turn off the VME and CAMAC crates, and the spdaq computer, all them located in the rack seating near the FP box in the S3 vault. Then, the system must be turned back on in the following order. First, CAMAC crate, second VME crate, and third spdaq.